You want sharpening stones that will be useful for the majority of your edges now, and that will remain useful as you expand both your tools and your sharpening toolkit in the future. Ending up with duplicate stones or ones that are no longer useful as you gain new knives or tools is a waste of money. The goal is to start with something that will stay with you as your needs develop.
The thumbnail test (not recommended for novices) - With this test you take your newly sharpened blade and run it oh-so-delicately over your thumbnail. If you feel it digging in even a tiny bit, it’s likely sharp enough. If on the other hand it just slips and slides across the surface of your nail it’s not sharp yet. Again, this test is only recommended for people with lots of experience handling knives and even then they’d probably be better off just grabbing a tomato or a piece of paper.
The goal when sharpening is to create a burr, which is a tiny whisper of metal left on one side of the blade. You'll know you have a burr when you can feel one smooth and one scratchy side to the edge. Warner's is formed in no time at all; I struggled. Nevertheless, eventually I got there. Once you've got the burr, it's time to move on to step three.
Some recommended products may use affiliate links. ProHuntingKnife.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Amazon and the Amazon logo are trademarks of Amazon.com, Inc or its affiliates.
The toughest angle to master is the angle at which you'll sharpen the edge of the knife. For a Japanese knife, that should be around 12-15 degrees. Before you reach for the protractor, a good test is to get roughly half an index finger's gap between the spine of the knife and the stone (see above). Remember to remove your finger before you start sharpening. For a Western-style knife, you want an angle of about 20°, so raise it ever-so-slightly higher.
Very interesting. If you work flat, 45 degree is what I was taught. Love the wet stones, especially the oiled ones. The nice thing about the leather part, is the mirror finish on a razor sharp blade which is a must if doing fine wood working, carving etc. A rough blade simply does not have the fine detailed dexterity. I find that the oiled sandpaper can work great as well, but found that the refined clay bars (white refined fired clay rounds and flats etc) does a wonderful job of keeping those razor edges refined, smooth as possible and then one can high polish them for smooth cutting. Believe me, when working wood for a flute, one wants that refined edge.! Learning how to hone a blade on a flat surface teaches one to work outside without a table/wall handy too...:) But we all have to start somewhere!:) Anyway, great stuff and a great start for those who want more from their tools!:) Cheers!
Put the pointed, narrow end of the sharpener up against the open end of the gut hook. The narrow, pointed end of the sharpener should face in toward the thickness of the blade, away from the edge of the gut hook. Match the angle of the sharpener to the original edge angle. This will maintain the correct sharpening angle and prevent you from getting cut by the blade tip. Hold the same angle when sharpening each side of the gut hook.
The kind of tech we love: compact, reliable, durable, attractive and cheap. Purists may feel that other sharpeners will produce a more perfect result but for 99% of the human race this sharpener will be everything the doctor ordered. Your blades stay sharp for a good long time thanks to the 2-stage sharpening process and if you’re a left handed chef you’ll love the fact that it works just as effectively for you as for anyone else.
If no metal is being removed from the edge of the blade, it’s considered honing. Whereas if metal is being removed from the blade edge this is considered sharpening. Certainly, even honing will result in some microscopic amounts of metal being removed from the blade edge but not enough to be visible to the human eye, so the above definition is basically a solid one.
In addition, the most prized of the natural Japanese Water Stones are quarried in the Narutaki District north of Kyoto, Japan and are commonly available as either bench stones or pocket stones in grits ranging from 120 to 12,000. On the other hand, synthetic water stones are made from Aluminum Oxide and commonly available as either bench stones or pocket stones as well in grits ranging from 220 to 8,000 and, although this is the same abrasive material used to make India Oil Stones, the difference between the two is that the binder that holds the abrasive together enables Water Stones to be much softer than India Oil Stones which, in turn, promotes faster cutting because the worn abrasive material breaks away more quickly and is replaced with fresh, sharp, abrasive material more quickly. In addition, because water stones do not become glazed or loaded with swarf like oil stones can, new abrasive particles are constantly exposed as the stone wears so it continues to cut consistently. Plus, they can be lubricated effectively with water (rather than oil which can ruin some water stones) which combines with the fine particles of abrasive from the surface of the stone to form a slurry which polishes the bevel as the stone cuts. However, it should also be noted that Water Stones do become uneven significantly faster than other types of whetstones although, their softness does make them easier to true again.
When the stone is intended for use on a flat surface, it is called a Bench Stone. On the other hand, small, portable, hand-held stones are referred to as Pocket Stones. Also, because Pocket Stones are smaller than Bench Stones, they are more easily transported but, they also present difficulty in maintaining a consistent angle and even pressure when attempting to sharpen longer blades. Consequently, Bench Stones are commonly used at home or in camp whereas, Pocket Stones are generally reserved for honing an edge in the field.
Once sufficiently wet, it's time to position the stone on something solid, so it doesn't move about during sharpening. Many come with holders, but you can just place it on a slightly damp tea towel on the table. The stone should be roughly perpendicular to your body, though Warner told me it is sometimes easier to angle it ever so slightly to the right (if you're right handed).
Diamond plates are available in various plate sizes (from credit card to bench plate size) and grades of grit. A coarser grit is used to remove larger amounts of metal more rapidly, such as when forming an edge or restoring a damaged edge. A finer grit is used to remove the scratches of larger grits and to refine an edge. There are two-sided plates with each side coated with a different grit.
The fit and finish on this product is amazing. He stone is beautiful and clearly high quality and very well cut. It’s different features on even such a small stone are huge. The leather cord and it’s unique knot is incredible. This is absolutely part of my edc, something I am happy to wear all the time. It’s useful and looks great too. Couldn’t be more happy with it.
This is my first time ordering from hayneedle, but you came thru with flying colors. I was so happy to see the delivery come so quick as stated. It was just as i hoped it would be, i now have my whetstone sharpening stone, to really get my kitchen knives as sharp as i can get them. This to me is the best way to sharpen a knife, it takes patience but the reward is worth it. Thanks Hayneedle you rock!!! Ray D.