Like all DMT® products, DMT sharpening stones are proudly made in the USA and will produce excellent, consistent results time after time, year after year. DMT's diamond sharpening stones feature the most diamond per square inch in the industry and a proprietary process that ensures near-perfect consistency in grit size, engineered to be the flattest sharpeners on the market. Simply put, DMT’s premium sharpening stones are best-in-class products with undeniable long-lasting value.

Most people don't think about sharpening knives until this vital kitchen tool is no longer sharp. The truth is that nothing impacts the longevity of your knives, or their daily performance, more than regular sharpening and maintenance. A dull knife in the kitchen is more dangerous than a sharp one when employees must force their way through cutting meat and slicing vegetables. As a result, daily sharpening and maintenance is easy, and most importantly, necessary. We're here to show you how to use a sharpening stone, including correct techniques and maintenance. The end result is a more efficient, and safer, set of knives!
I can personally verify that this will get your knives very sharp. I will spare you all the gory details, but the picture is of the instructions the ER sent me home with after stopping the bleeding and patching me up. I have to say, that’s not what I had in mind regarding “Thanksgiving tips”. So: not only will knives slide easily through spinach, but they will go through finger and fingernail like a hot knife through butter after being sharpened by this whetstone. Very clean, straight cut. Impressive, really. Just take it slow and don’t be a moron like me.
In addition, there are three broad grades of Japanese Water Stones consisting of the Ara-to (rough stone), the Naka-to (middle/medium stone) and, the Shiage-to (finishing stone). However, it should be noted that the various grades of natural Japanese Water Stones vary widely in both density and grit size from stone to stone and thus, they do not translate well to American or European abrasive standards. Furthermore, because they are significantly softer than Novaculite, Japanese Water Stones must be flattened more often and do not last as long as a either Novaculite or Coticule stones. But, because they form a slurry of fine particles when used, they also do a superior job of both cutting and polishing.
Works well. Just got it today, sharpened two pocket knives, one a 8Cr13MoV Chinese steel, the other s30v American steel The stone made short work of both steels (which were pretty sharp already). But notably was able to make the s30v hair shaving sharp easily, something I've had trouble with. Inexpensive and useful, I love this stone. It's not the Ninja sharp 8000+ grits that you can find, but for pocket knives and EDC, it's perfect and inexpensive. Get One!!!!!!!!!!!!
Once the burr is removed, it's time to test the sharpness with paper. Hold a piece of newspaper at about 45°, with a bit of tension, and slash lightly with each point of the blade. If it cuts through easily, your knife's sharp. Warner speedily lacerated his newspaper, but I of course struggled. There is an element of technique involved, he reassured me. 
You've acquired a good chef's knife, you're using it almost daily to make tasty dinners for the family, and it's stored in a nice knife rack or a magnet for safekeeping. So why stop there? Keeping that knife's edge fine will make cooking not only safer but, let's face it, much more fun. Whether you've spent £150 on a high-end knife or under a tenner on a dinky paring knife, keeping it sharp is crucial. 
There will be a drawer that extends into the mechanism under the abrasives. Any detritus from the sharpening process drops into this drawer. Exactly where the drawer is located will differ from sharpener to sharpener but it shouldn’t be hard to find. Remove the drawer flick any material into the wastebasket and then wipe out the drawer with a damp cloth or tissue. You may want to use work gloves and goggles to protect your hands and eyes from any loose metal shavings. Once the drawer is clean and dry replace it. The exact means by which the sharpening mechanism itself is cleaned will vary from manufacturer to manufacturer. Consult your owners guide for specific details. Make sure you don’t introduce any grease or other lubricants into the sharpener unless specifically directed to do so by the owner’s manual. Also, the outside of the sharpener should come perfectly clean with just a damp cloth. Avoid using commercial cleaners or abrasives of any kind.

To use Al's method, take a black felt pen and shade in the bevel of the knife. Then take two strokes on the stone and examine the edge. If you have maintained the proper angle then all the black will be gone. If you see black on the top of the edge it means you are holding the back of the knife too far from the stone. If there is black on the bottom of the edge but the top is clean then you are laying the knife too flat on the stone and you need to raise it a bit. Repaint the edge and try it again. Once you discover what the right angle looks like then just maintain that.
Now it's time to polish. This is when you'll swap over from the coarse grit to the finer grit (make sure this side is wet, too). I found the knife still had a bit of grime on it, so I gave it a wipe clean beforehand. The motion is exactly the same as with sharpening, but you can apply slightly less pressure, and limit to roughly 30 strokes on each side. 
100% Brand NewA fine-grained whetstone lubricated with oil, used for fine sharpening.The Ruby sharpening stone and Agate Stone,For Polishing,Sharpening.Can Make Mirror surface, mirror finish.The Ruby Sharpening stone is made from sintered crystals of synthetic ruby.It’s extremely hard, maintain their shape well and are resistant to wear.Size:50*25*10mm(1.97*0.98*0.39 inch)Model:3000 & 10,000 GritColor: red & whiteMainly used in industrial instrumentation, precision parts, miniature knives, stones, measuring tools, cutting tools, instruments, carbide, etc.Package included:1x Two Sides Jade SharpenerNote:Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error i.
Removing the burr is fairly simple. You'll need a leather strop or block (this sort of thing), which is designed to catch the metal fibres from the knife. You could do it with a fibrous tea towel or some newspaper if you like, but I'd suggest going with leather to begin with. The motion is fairly similar to sharpening. Draw the knife over the leather, going away from the edge at roughly the same angle as when you sharpened. 
I do have to question the grit ratings of these stones. I didn't notice anything before using them, but after a day, the 2000 grit actually felt courser than the 1000 grit side of the other stone. Whether that could be a byproduct of other factors or an indication of the more obvious, being that the grit ratings aren't accurate, I don't know. But that seemed to be the main criticism of cheaper whetstones, that their grit ratings often aren't accurate. Or maybe it's less a problem with accuracy and more a difference that most synthetic stones might have in common when being compared to much pricier natural stones?
Grit choices should fall in line with the steel used to make the knives you plan to sharpen. If your knives are all European, relatively soft steel knives, then you could finish off your knives at the 1,000 – 2,000 grit level. There is a lengthy explanation regarding this topic but suffice it to say that at 2,000 grit, these knives can be made extremely sharp.

We offer a series of oilstone packages that combine India and Arkansas stones and are very reasonably priced. At 8" long by 2" wide these stones are not as wide as some other types, but still wide enough for many edges and are plenty wide for knife sharpeners. Available in four price levels, these kits are a great opportunity for the beginning sharpener on a budget.
Put the pointed, narrow end of the sharpener up against the open end of the gut hook. The narrow, pointed end of the sharpener should face in toward the thickness of the blade, away from the edge of the gut hook. Match the angle of the sharpener to the original edge angle. This will maintain the correct sharpening angle and prevent you from getting cut by the blade tip. Hold the same angle when sharpening each side of the gut hook.
×