Honing steels are another story altogether. Honing steels are those instruments that look light a saber (light or otherwise) which you use to gussy up the edge of the blade periodically before using it. These do wear out every few years or less, depending on how often you use them. If you are unsure whether your honing steel is worn out run your finger around it. If it feels smooth all the way around then it’s time for a replacement. Not to worry though, they’re really affordable. One thing you may want to keep in mind about honing steels is that they typically won’t do much to hone the edge of some super hard knives, such as Japanese Global brand knives.
It is better to understand the difference in sharpening stone materials before you are going to make any decision. Among the available options in the market today, Waterstone, oilstone and diamond stone are the most common type of sharpening stone. Each of stones comes with advantages and disadvantages. Waterstone and oilstone are available in natural and synthetic models. Synthetic are the most common and easy to find as man makes them. As the use of natural stones (e.g. original Arkansas or Japanese natural whetstones) is has diminished in popularity, they are beginning to rare in the market. Artificial stones have a more consistent particle size and controlled with a tight mechanism in providing high-quality sharpening stone.
We tend to recommend natural Japanese water stones only to experienced users who are thoroughly familiar with the synthetic Japanese sharpening stones. Natural stones are not to everybody’s taste and there are inevitably many uncertainties with regard to their grit grade, which cannot be determined exactly, their hardness and their suitability for certain types of steel.
I purchased this set together with the 400/1000 grit stone assuming that some of my knives were quite dull and would need work on a coarse grit stone. Premium Whetstone Sharpening Stone 2 Side Grit 400/1000 | Knife Sharpener Waterstone with NonSlip Rubber Base & Flattening Stone. This is my first wetstone. First off I tried to sharpen my Chicago Cutlery boning knife. This knife is nearly thirty years old, has been abused in may ways and was quite dull. It was very difficult for me to get a burr on this blade, which I attribute to poor technique. Next I moved on to my Henckels Professional S paring and chef's knives. The paring knife was moderately sharp and was modestly improved after working over all three grits of stone. It would cut paper but again it was difficult to develop a burr with this blade. Undaunted I switched to the chef's knife. This knife is twenty years old and has never been professionally re-sharpened. I have sharpened it twice with a Lanksey sharpening system which marred the finish but did put a good edge on the blade. Lansky Standard Coarse Sharpening System with Fine Hones. The chef's knife was moderately dull and had several pits visible on the cutting surface. I modified my technique for passing the knife over the stone and worked the chef's knife over the 400 grit stone aggressively and eventually I was able to get a burr to form from the tip of the knife all the way to the handle. From there it was a simple process of reforming the burr on the 1000 grit stone and then finishing on the 6000. After sharpening, the chef's knife easily and cleanly slices a tomato with very light pressure and is in my opinion very sharp. Not sushi knife sharp but more than enough for the chopping and slicing I expect of it. I'm looking forward to going back and working both the boning knife and the paring knife over again. Don't expect a good result from this product the first time you use it. Watch videos on using a wetstone, expect to spend at least twenty minutes per knife at first, and practice forming a burr. If you can form a burr, you will be able to successfully sharpen your knife.
I would say they are worth the money. Go for it. I took a blunted Pampered Chef kitchen knife from completely dull to razor sharp in about an hour (of bumbling and repairing mistakes LOL) heavy grinding. If you have a severely damaged blade, grab one of those cheesey two sided stones from Harbor Freight to do your heavy grinding. From there these stones will work very well.
So, as you can see, there are numerous different types and grades of whetstones on the market today and each has its advantages and disadvantages. Therefore, the right practice to choose the right sharpening stone for you is to choose a whetstone material based upon how fast you need to remove metal and how fine an edge you need. For instance, although they are often the most expensive type of whetstone, diamond hones generally cut the fastest even in their finer grits followed by Crystolon Stones and then India Stones which are then generally followed by Japanese Water Stones and then by Novaculite, Belgian Blue, and Coticule whetstones in terms of how fast they remove metal. However, it should also be noted that the rougher an edge is, the less sharp it is while, the more polished an edge is, the sharper it is and thus, rough edges are fine for some tools while other tools require a much finer edge and, hunting knives require the finest edge of all. Therefore, the trick to choosing the proper whetstone for any given sharpening purpose is to purchase multiple stones with varying grits to accomplish each given task from cutting an initial bevel or defining a damaged edge to refining an existing edge to polishing it. We hope this article helped you. Feel free to leave a comment below if you have questions.
×