In addition, the most prized of the natural Japanese Water Stones are quarried in the Narutaki District north of Kyoto, Japan and are commonly available as either bench stones or pocket stones in grits ranging from 120 to 12,000. On the other hand, synthetic water stones are made from Aluminum Oxide and commonly available as either bench stones or pocket stones as well in grits ranging from 220 to 8,000 and, although this is the same abrasive material used to make India Oil Stones, the difference between the two is that the binder that holds the abrasive together enables Water Stones to be much softer than India Oil Stones which, in turn, promotes faster cutting because the worn abrasive material breaks away more quickly and is replaced with fresh, sharp, abrasive material more quickly. In addition, because water stones do not become glazed or loaded with swarf like oil stones can, new abrasive particles are constantly exposed as the stone wears so it continues to cut consistently. Plus, they can be lubricated effectively with water (rather than oil which can ruin some water stones) which combines with the fine particles of abrasive from the surface of the stone to form a slurry which polishes the bevel as the stone cuts. However, it should also be noted that Water Stones do become uneven significantly faster than other types of whetstones although, their softness does make them easier to true again.
Silicone Carbide whetstones on the other hand, are the fastest cutting of the three types of oil stones and the stones made by Norton are called Crystolon Stones. Also they too are graded as either fine, medium, or coarse stones depending on their grit. But, although these stones will not produce an edge as fine as Arkansas Oil Stones or India Oil Stones, their fast cutting ability makes them ideal for sharpening tools as well as for cutting the initial edge bevel on extremely dull knives or repairing the edge on damaged blades. Last, because they sharpen so quickly, it a common practice to start with a coarse Crystolon Oil Stone and then progress to either a medium or fine India Oil Stone and then to finish with an Arkansas Oil Stone.
We regret that due to technical challenges caused by new regulations in Europe, we can for the time being no longer accept orders from the European Union. If you reside in the UK you can continue to order from our UK websites or shop from our locations and partners. Visit West Elm at www.westelm.co.uk and Pottery Barn Kids at www.potterybarnkids.co.uk.
All stones require either water or oil as a lubricant to sharpen the knife. We prefer water stones because they’re easier to use, less messy and don’t have the possibility to go rancid like oil does. If you choose a water stone, all you have to do is either add water to the stone before placing the knife on the surface, or soak the stone in water for 10 minutes before use. You’ll want to read the instruction for the stone you purchase to find out how to use it properly.
Over the course of two days I re-sharpened nearly a dozen old blades, including removing the secondary bevel on an old stainless Ontario saber-grind Navy diver's knife, convexing the edge on flat ground 1095 Schrade 55 that also came with a secondary bevel, and fixing a broken tip on an old Kershaw folder. These stones made quick work of the Schrade and Kershaw. Both had completely new edge geometry within 30 minutes apiece. The Kershaw looked like-new, as if the tip had never broken. And the Schrade cut much better than it's secondary bevel would previously allow, regardless of how sharp I got it with a ceramic rod and strops. The Ontario took a little more work, as it had been abused a little the last time I'd held it, over 25 years ago and was as dull as a case knife - one of the reasons I decided to go ahead and do a full saber grind - well, a slightly convexed saber, I suppose would be more accurate. But within under an hour of using the two stones and a couple leather strops (one with black compound, another with green), the Ontario was shaving sharp again too.
I bet those Vikings, relatives of mine no doubt, never had it so good. They never had surated blades to sharpen or needed to wear cool things around their necks to woo the women (they just grabbed them by the hair I guess). I love my stone. So useful and beautiful. I always have spit to wet it with, and I always have a way to sharpen my tool. Wazoo makes high quality products. I give them the highest rating I have. Dudes!
Technically, the name whetstone can be applied to any form of sharpening stone, regardless of what cutting fluid is typically used with it. However because whet sounds like wet, many hear the word and assume that it refers to a stone that is used wet with water. Actually, water stones, oil stones diamond stones and ceramic stones are all forms of whetstones. So, while all water stones are whetstones, not all whetstones are water stones.
Some of the videos I watched suggested soaking the stone for 12-15 minutes prior to use. One suggested using vegetable oil on the surface versus water/soaking (I used water and presoaking it for 15-minutes). So instead of a simple 'out-of-the-box-and-use' approach, it required a bit of research before sharpening a knife. Otherwise I would have given this product a 5-star rating.