The newly designed dual-sided combination whetstone from Fallkniven features a super fine white ceramic stone (0, 1 micron) with a grit of 1400 to 2000 and the dark grey ceramic stone is made of synthetic sapphires (1 micron) and has a grit of 800-1000. There is no need to add any oil or water, just lay the blade on the stone, raise the blade's spine and deburr your blade on the grey side until it has a razor-sharp edge and then use the smooth white side to get a nice polished edge.
The unique three stone system features a 6" medium Arkansas, 6" fine Arkansas and 6" coarse synthetic stone mounted on a molded plastic triangle with handles on the end for easy stone selection. The sturdy molded plastic base has non-skid rubber feet for safety, a V-shaped trough to catch oil drippings and easy-to- read stone identification markings.
The most important aspect of a sharpening stone is the grit. If you have knives that have taken a beating and are either nicked up or really dull, you’ll need a courser stone to get it back into shape. And in order to put an exceptionally sharp edge on an already sharp knife, you’ll need a finer grit stone. If your knives are already in pretty good shape and just need a touch up, buying just a finer grit stone might be enough, but don’t think you can get away without a courser stone for knives that need more TLC. It is possible to buy a combination, or two-sided sharpening stone.
Shapton Glass 320, 500, 1,000, 2,000 and 16,000. I have the 4,000, and 8,000, they are absolutely fine, great in fact but I just don’t use them as much as the others. These stones excel on knives made of hard steel, the hardest steel is no match for these. This does not mean you can’t sharpen hard knives on the Naniwa brand of course, you can. I have been using this particular brand of stone for many years and I absolutely love them.
Let’s start with Arkansas. If you have heard about Arkansas oilstone, it uses the Novaculite stone that mined in Arkansas. The most expensive of Arkansas stone is the Hard Translucent model that begins to rare in the market. If you want to shop for Arkansas, they are available in different grade starting from Soft Arkansas, Hard Arkansas, Hard Black Arkansas and Hard Translucent Arkansas. The finest grade of Arkansas can shape such of mirror polishing edges.
You will be given access to our useful online learning material: a set of videos and articles to help you improve your sharpening technique. These resources were made by professional knife sharpeners, specifically for beginners and intermediate sharpeners. The articles and videos will guide you and teach you knife sharpening from scratch, also covering more advanced techniques. You can also get in touch with us anytime if you have any questions concerning sharpening specific types knives.
The goal in sharpening a serration is to maintain the ramp of the serration right to the edge. You do not want to create an edge bevel. Therefore we once again recommend the trusty felt pen trick. Paint the serration to be sharpened and follow your process. Evaluate if you are removing all the black. It should not take more than 5-8 strokes to resharpen if your angle was correct. Rotate or spin the sharpener as you go for the most even, consistent sharpening.
Over the course of two days I re-sharpened nearly a dozen old blades, including removing the secondary bevel on an old stainless Ontario saber-grind Navy diver's knife, convexing the edge on flat ground 1095 Schrade 55 that also came with a secondary bevel, and fixing a broken tip on an old Kershaw folder. These stones made quick work of the Schrade and Kershaw. Both had completely new edge geometry within 30 minutes apiece. The Kershaw looked like-new, as if the tip had never broken. And the Schrade cut much better than it's secondary bevel would previously allow, regardless of how sharp I got it with a ceramic rod and strops. The Ontario took a little more work, as it had been abused a little the last time I'd held it, over 25 years ago and was as dull as a case knife - one of the reasons I decided to go ahead and do a full saber grind - well, a slightly convexed saber, I suppose would be more accurate. But within under an hour of using the two stones and a couple leather strops (one with black compound, another with green), the Ontario was shaving sharp again too.
The stone is of good quality. It can be used with water or oil - but not both at the same time of course :) ... What I really want to mention is that Hayneedle has amazing customer service - no joke! My stone was shipped from the mfg. not hayneedle whse and there was a chip on one corner. They said - we can't have that! ... So they took care of the whole matter with NO cost to me and they were very friendly as if I was doing them a favor!
A: That depends almost entirely on how often you use them. If you are a professional chef who uses his or her knives every day then you should hone them every time you use your knives. But honing has its limits and over time your edge is going to become dull no matter what. Therefore your knives will need to be sharpened at least several times a year. Some chefs, in fact, will use a whetstone on an almost daily basis in order to ensure their knives are always razor sharp. Most of us, however, are not professional chefs and may not even touch our kitchen knives for days at a time. In that case, it’s probably a good idea to hone the edge after every couple of uses and have your knives sharpened once a year.
Now move the blade – with a little pressure – in regular movements up and down along the sharpening stone. Always maintain the angle between the blade and stone. You will notice a burr become visible after five or so movements. Mentally divide the blade into three sections if the knife has a large blade. Always start with the tip and work back towards the bolster.
Whichever method you choose, be it a waterstone (also known as a whetstone), or a pull-through (either V-shaped or ceramic wheels) it's important to regularly hone your knife with a honing steel, which we'll also cover below. You'll be pleased to hear that you won't have to reach for the stones too regularly – once every two or three months should suffice.
We're not completely sure but we think we now have the largest selection of sharpening stones on the face of the earth. If you're interested in something and don't see it here please contact us and we'll try to get it. Most of the stones you see here are Japanese water stones, both synthetic and naturals. There is also a wide selection of stone holders, flatteners, and other items that will help you get a razor sharp edge on all your sharp tools and knives.
The stones from Shapton are probably the hardest of all Japanese sharpening stones. They will remain flat for a long time. They are therefore the best choice if you are looking for a relatively coarse stone that cuts quickly without having to be dressed repeatedly. The finer-grained stones also work very well. But Shapton stones do not provide the mirror finish you can achieve with softer stones.
A good whetstone and a little practice will keep all of your knives sharp and in perfect condition. The beauty is that it doesn’t take much effort to learn, just a good bit of practice to get the angle right and keep a consistent angle while you’re sharpening. Whetstones are available in department stores or online, and while they range in price based on the fineness of the grit, this thread at eGullet can help you pick a good grit to start with.
I really liked this whetstone! I had a Smith's pocket sharpener that could get my knife sharp enough for working around in the yard (I have an Opinel no.8). However, in doing a little research I found that the sharpener was only around 600 grit on the finest setting. So this BearMoo 1000/4000 grit looked like the perfect step up, and it turned out to be the perfect stone for me. The pictures are an accurate representation of what you get. The removable rubber base was helpful when switching from one side to the next, and it kept the stone from sliding around. The instructions say that the stone can work with either water or oil, but that water is preferred. It said to leave the stone soaking in water for five minutes, and the stone worked like a champ. I especially liked how the instructions gave you an approximate time of how long the stone takes to sharpen a knife -- it just helped give me an idea that it would take about 15-20 minutes on the 1000 grit side, and then another 10-15 minutes on the 4000 grit. Just turn on a TV show!
You need to adjust your fingers as you move the knife back and forth. Because sharpening takes place under your fingers, start with them at the tip and, as you pull the knife back toward you, release pressure completely and pause. Then, shift your fingers just a little down the blade toward the heel. This finger dance is critical and takes time getting used to.
I am just starting out sharpening with whet stones. I have found these stones to be very nice and the instructional videos that come along with the set on knifeplanet are extremely helpful to anyone starting out. The cost of the set was very reasonable and seems to be a great value. The customer service is amazing, I lost the site for the videos and sent an email to get the information and immediately there was a reply with all of the links that I needed. I appreciate their attention to their customers!!
Furthermore, Novaculite consists of several different layers of stone of different densities, grit sizes, and colors. Thus, the red Novaculite layer (aka Washita Stone) is the both the softest and most coarse while, the next most coarse/hard grade is the grey/white Soft Arkansas stone; both of which cut relatively fast for a hard whetstone material and thus, they are an excellent choice for refining a bevel. Then, the next grade of coarseness/hardness is the hard Arkansas stone which is used to polish the bevel rather than define it and, last there are the grades of Hard Black and Hard Translucent Arkansas stones which are used for extremely fine honing and polishing of a cutting edge. Plus, it’s also the primary material in “Charnley Forest” (English) and “Turkey” oilstones.
However, it should also be noted that “water stones” are generally significantly softer than oil stones and thus, water stones generally cut faster than oil stones but, they also have to be flattened more often that oil stones do. Furthermore, it should be noted that some water stones must be soaked in water for several hours prior to use whereas, others are of the “splash and sharpen” variety and thus, they only need to be soaked for a few minutes before use and then wetted down occasionally during sharpening process. Diamond hones on the other hand are more durable than either water stones or oil stones and, because they generally have a more coarse grit, they cut faster than natural whetstones. Plus, due to their construction, they never need truing and, in fact, coarse diamond hones are often used to flatten both natural and synthetic whetstones.
In most cases a sharpening stone will be a combination of sharpening grains and a binding agent. However, in case of a Ardennes Coticule it is a completely natural product. The grains have cutting edges which enables them to sharpen your knife. As soon as a sharpening stone is used little pieces of the grains break off, revealing a new cut ing edge. The higher the number, the finer the grain. Stones with coarse grains (up to grain 400) can be used to shape the blade of a blunt knife. You can subsequently take care of the fine finish with a stone with a smaller grain.
Lubricant. Most knife sharpening experts recommend you use some sort of lubricant when sharpening your knife. The lubricant can come in a variety of forms, from water to oil. Most of the literature out there recommends mineral oil to be used for knife sharpening. The lubricant reduces heat from the friction that is created from sharpening your knife. Too much heat can actually warp your blade. Lubrication also helps clear out the debris, or swarf, that is created as you grind your knife blade on the stone. You can pick this up at most hardware stores for about $5. I used Norton Sharpening Stone Oil in the video.
When starting out sharpening, it won’t be long before you hear about the “toothy” vs “polished” edge. It will suffice to know that a 1k stone is going to give you an edge that will perform beautifully as will a knife finished at 5k. There is a belief that a knife that has a highly polished finish, 5k and up will be so polished that it’s toothy goodness will be erased. This knife will not bite into the skin of a tomato for example because the edge is too polished, it will slide over the top. This is not always true, if the knife has been sharpened well, i.e. if Side A and Side B of the blade meet precisely at the Apex of the knife, that edge will slide into a tomato quite beautifully. I have seen many brand new Japanese knives with highly polished 8k edges that no tomato skin can stand up to.
Sharpening stones have been around since the dawn of civilization for a very good reason: they work. Yes, they’re more labor intensive than most electric sharpeners but they also allow you an unprecedented level of control. Once you get used to something like the Fallkniven DC3 Diamond/Ceramic Whetstone Sharpener you may never take out your electric sharpener again.
At age 10, Terada learned the basics of sushi from his father and then went on to attend RKC Chef's School in Kochi, Japan from 1987-1989. He soon earned a nickname for his fast knife, attention to detail, divine presentation and ability to create new dishes and accents based on traditional Japanese cuisine. After graduating RKC Chef School, he was called to serve under Master Chef Kondo at Yuzuan restaurant in Kochi, Japan from 1989-1992. Mr. Kondo is the master of Kansai style cooking, considered to be the high-end of Japanese cuisine. Terada earned the title Master Sushi Chef by becoming the standing head sushi chef & can serve Fugu (Japan Licensed) to the public.
Diamond hones are made from very small, industrial grade, diamonds adhered to the face of a metal or plastic plate. Also, because Diamonds are so much harder than any of the other sharpening materials, they tend to cut very fast and last much longer than the other whetstone materials. But, they are also often more expensive to purchase. In addition, Diamond Stones generally consist of three different styles consisting of a solid metal plate coated with an adhesive and diamond dust with holes in the plate to allow the swarf to escape, a solid plate without holes for sharpening tools with corners that might catch in the holes, and a plastic plate with islands of exposed plastic interspersed with the adhesive and diamond dust to act as a lubricant.
We’ve shown you how to keep knives sharp before, and even discussed why water stones are best, but this crash course is quick, fast, and gets to the point. In most cases the most the average person at home can do is either hone their blade with a honing steel, which straightens and lines up the blade’s edge, but it doesn’t sharpen it. Alternatively you could run it through a handheld or electronic sharpener, but depending on the model you use it can do more harm than good.