The composition of the stone affects the sharpness of the blade (a finer grain, usually, though not always, produces sharper blades), as does the composition of the blade (some metals take and keep an edge better than others). For example, Western kitchen knives are usually made of softer steel and take an edge angle of 20–22°, while East Asian kitchen knives are traditionally of harder steel and take an edge angle of 15–18°. The Western-style kitchen knives are generally in the range of 52–58 on the Rockwell scale, which denotes the relative hardness of a material.
You need the right size of sharpening stone that fit the type and size of your blades and tools. In general, 6-inches stones are the smaller models and 8-inches are the larger ones. The stones larger than 8 inches are work best for big-sized blades and tools. You may also find sort of ‘pocket knife sharpener’ out there. Most of the credit card sized sharpening stone are smaller than 6 inches and ideal for on the go sharpening not for regular basis.
Functionality – If you have experience with the stick or sharpening stone you likely don’t want or need anything else. If, however, you are in search of an electric-powered sharpener you’ll want to consider how many “stages” you need in your sharpener. In a typical 3-stage sharpener the first stage is the coarsest and does most of the heavy lifting required to turn the edge from dull to sharp. The second stage will have finer grain sharpening wheels. These are used to hone the edge, that is, to smooth out the burrs left by the coarse first stage. A third stage will refine the edge even further and remove any debris left over from the sharpening process.
A: Most chefs have their own personal favorite and that’s what it comes down to for just about everybody; personal choice. If you’re the kind who likes to get personally involved in the process you might want to opt for a stone or stick knife sharpener. These will allow you a certain amount of satisfaction knowing it was your expertise that produced the razor sharp edge. Others, however, are quite content to let the machine do the work and that’s fine too.
So you are going to start at the heel and you are going to time it so that it goes all the way across. You go from one side to the other. You also want to make sure that your stone, I am not going to use as much pressure as I normally would because I cannot mount it on this showcase, you want to alternate from side to side to keep your bevel centered. Some people will take and do three times on one side and then three times on the other, the problem is that your backhand is never as good as your forehand and you end up cheating and you are going to end up with a blade that is offset. That is going to take it and thin down, you are going to get a thin bevel right on the edge. Once you get that V established, you can go from the coarser side to the finer side.
A: Like cars, knife sharpeners run the gamut from basic to luxury and like cars the price can vary from extremely affordable to more than some people might want to spend. You can get a high quality sharpener that will put your knives through a 2 or 3-stage process which will result in an incredibly sharp edge for less than $20. Or you can buy a mechanical sharpener that will produce a virtually flawless edge for $200+.
The newly designed dual-sided combination whetstone from Fallkniven features a super fine white ceramic stone (0, 1 micron) with a grit of 1400 to 2000 and the dark grey ceramic stone is made of synthetic sapphires (1 micron) and has a grit of 800-1000. There is no need to add any oil or water, just lay the blade on the stone, raise the blade's spine and deburr your blade on the grey side until it has a razor-sharp edge and then use the smooth white side to get a nice polished edge.
The coarse stone will cut the metal off quicker but it is going to give you a rougher edge but that way the job gets done quicker, without the oil. It is not as messy. This is just a real simple set up. If you do wood work you can make a little wooden box and rout it out. In this particular case it is just a 2x4, stone traced out, finishing nails tapped down so they are deeper than the stone so when you drop the stone in, if you are at a workbench you can C-clamp it down in place or you can hold on to it.
We’ve shown you how to keep knives sharp before, and even discussed why water stones are best, but this crash course is quick, fast, and gets to the point. In most cases the most the average person at home can do is either hone their blade with a honing steel, which straightens and lines up the blade’s edge, but it doesn’t sharpen it. Alternatively you could run it through a handheld or electronic sharpener, but depending on the model you use it can do more harm than good.