This is a good size stone and has the two different grits needed for knife sharpening. No instructions were included, but there are many websites with written and video instructions, so this is not an issue for most people. A fair amount of dust is generated during the sharpening process, so protect the work surface and wash the knife after sharpening is completed.
3. Place the knife blade flat on the stone and raise it to a 10 to 15 degree angle. The key to knife sharpening is maintaining a constant angle. Different knives require different sharpening angles. For a pocket knife, shoot for a 10 to 15 degree angle. This will give you an edge that’s sharp enough for most daily needs, but not sharp enough to perform heart surgery. Keeping a constant angle by hand takes a lot of practice. If you’re having difficulty, you might consider investing in a sharpening guide. It takes all the guess work out of maintaining the needed angle. They cost about $10.
Beginning on the right side of the knife, move from tip to heel and heel to tip, then flip the knife and repeat. For the left side, it’s opposite—start at the top of the stone to reach the heel area completely. So, you will move from heel to tip and then tip to heel. Remember to apply and release pressure as you did earlier, exactly the same as in Step 2, but with light, refining pressure.
Grinding is generally done with some type of sharpening stone. Sharpening stones come in coarse and fine grits and can be described as hard or soft based on whether the grit comes free of the stone with use. Many sources of naturally occurring stones exist around the world; some types known to the ancient world are no longer used, due to exhaustion of former resources or the ready availability of superior alternatives. Arkansas, USA is one source for honing stones, which are traditionally used with water or honing oil. India is another traditional source for stones. Ceramic hones are also common, especially for fine grit size. Japanese water stones (both artificial and natural) come in very fine grits. Before use, they are soaked in water, then flushed with water occasionally to expose new stone material to the knife blade. The mixture of water and abraded stone and knife material is known as slurry, which can assist with the polishing of the knife edge and help sharpen the blade. Generally, these are more costly than oilstones. Coated hones, which have an abrasive, sometimes diamonds, on a base of plastic or metal, are also available.
The Sunrise Pro doesn’t have the pedigree of some other knife sharpeners on our list but it performs as advertised and that’s all that matters. For a relative song you get to restore all the knives, steak knives, cleavers in your kitchen to near pristine condition. It’s easy to use and the nice strong suction cup on the bottom means you can put the band aids away.
You will be given access to our useful online learning material: a set of videos and articles to help you improve your sharpening technique. These resources were made by professional knife sharpeners, specifically for beginners and intermediate sharpeners. The articles and videos will guide you and teach you knife sharpening from scratch, also covering more advanced techniques. You can also get in touch with us anytime if you have any questions concerning sharpening specific types knives.
In addition, the most prized of the natural Japanese Water Stones are quarried in the Narutaki District north of Kyoto, Japan and are commonly available as either bench stones or pocket stones in grits ranging from 120 to 12,000. On the other hand, synthetic water stones are made from Aluminum Oxide and commonly available as either bench stones or pocket stones as well in grits ranging from 220 to 8,000 and, although this is the same abrasive material used to make India Oil Stones, the difference between the two is that the binder that holds the abrasive together enables Water Stones to be much softer than India Oil Stones which, in turn, promotes faster cutting because the worn abrasive material breaks away more quickly and is replaced with fresh, sharp, abrasive material more quickly. In addition, because water stones do not become glazed or loaded with swarf like oil stones can, new abrasive particles are constantly exposed as the stone wears so it continues to cut consistently. Plus, they can be lubricated effectively with water (rather than oil which can ruin some water stones) which combines with the fine particles of abrasive from the surface of the stone to form a slurry which polishes the bevel as the stone cuts. However, it should also be noted that Water Stones do become uneven significantly faster than other types of whetstones although, their softness does make them easier to true again.
Therefore, the first step to choosing a whetstone is to determine your intended purpose and then choose your whetstone accordingly. For instance, when sharpening tools that do not require a fine edge, you should choose a relatively soft, coarse, stone such as a Norton Crystolon water stone. However, for sharpening tools that do require a fine edge, a somewhat harder Norton India oil stone would be a good choice. But, for sharpening hunting knives where an exceptionally fine edge is required, a Novaculite or Coticule oil stone would be the best but, most expensive, choice. So, the process of choosing the correct whetstone for any given purpose is to first determine how fast you would like for the stone to cut and how fine an edge you need, and then choose either a soft, coarse, stone or, a hard, fine, stone of the appropriate type and grit.
The type of stone refers to the material it is made with. You can find many different types, including diamond, ceramic, natural stone, and synthetic. I would only suggest diamond if you’re planning to be sharpening only ceramic knives. Many of the stones you’ll find on Amazon or other retails are made of Corundum, which is a crystalline form of aluminium oxide. It’s a fine choice for a beginner sharpening stone.
To use Al's method, take a black felt pen and shade in the bevel of the knife. Then take two strokes on the stone and examine the edge. If you have maintained the proper angle then all the black will be gone. If you see black on the top of the edge it means you are holding the back of the knife too far from the stone. If there is black on the bottom of the edge but the top is clean then you are laying the knife too flat on the stone and you need to raise it a bit. Repaint the edge and try it again. Once you discover what the right angle looks like then just maintain that.
I've been using this stone for months and have started to find that, while the fine side does provide a nice sharp edge, the 400gr side is wearing my knives unevenly, which causes me to be unable to finely sharpen the entire length of the blade when moving to the fine side. The logo that is put in the middle of the 400gr side of the knife is causing more material to be removed than the rest of the blade when I'm sweeping across. I even verified this by going straight down the length of the fine side and watching the wear pattern come from the material coming off of the knife onto the stone.
Last, it should be noted that dual-sided Coticule/Belgian Blue whetstones are also sometimes available which have a layer of Belgian Blue stone on one side and a layer of Coticule on the other. Thus, these whetstones provide a softer, more coarse, grit on one side and a harder, finer, grit on the other. Plus, due to the inherent toughness of the Belgian Blue stone, these dual-sided stones do not require a substrate layer.
Works well. Just got it today, sharpened two pocket knives, one a 8Cr13MoV Chinese steel, the other s30v American steel The stone made short work of both steels (which were pretty sharp already). But notably was able to make the s30v hair shaving sharp easily, something I've had trouble with. Inexpensive and useful, I love this stone. It's not the Ninja sharp 8000+ grits that you can find, but for pocket knives and EDC, it's perfect and inexpensive. Get One!!!!!!!!!!!!
To take off the fine scratches and burrs left by coarser stones, and to polish the surface, you can use stones starting at around 2000 grit. There is theoretically no upper limit, but stones above about 10000 grit achieve practically no measurable improvement in the edge. It is also interesting to note that above 8000 grit, there is no Japanese measurement standard. For stones labelled as having a finer grit, you simply have to take the manufacturer's word for it.
Learning sharpening technique requires focus even without worrying about the stone itself. Stones that require frequent flattening, soaking and cleaning, or that take a long time to create an edge can be a source of frustration to some beginning sharpeners. Keep in mind your willingness perform regular maintenance when choosing a starting set of stones.
Using the strength of industrial high precision superior mono-crystalline diamonds, Diamond Machining Technology (DMT) have created a durable longer-lasting flat sharpening surface that will efficiently sharpen, hone, deburr and polish almost any type of knife or cutting tool. The DMT set contains 3 one-sided whetstones that have extra-fine, fine, and coarse grits which means you have a complete sharpening system at your fingertips.
Diamond plates are available in various plate sizes (from credit card to bench plate size) and grades of grit. A coarser grit is used to remove larger amounts of metal more rapidly, such as when forming an edge or restoring a damaged edge. A finer grit is used to remove the scratches of larger grits and to refine an edge. There are two-sided plates with each side coated with a different grit.