The composition of the stone affects the sharpness of the blade (a finer grain, usually, though not always, produces sharper blades), as does the composition of the blade (some metals take and keep an edge better than others). For example, Western kitchen knives are usually made of softer steel and take an edge angle of 20–22°, while East Asian kitchen knives are traditionally of harder steel and take an edge angle of 15–18°. The Western-style kitchen knives are generally in the range of 52–58 on the Rockwell scale, which denotes the relative hardness of a material.
Cerax and Suehiro stones from Suehiro are a little harder, and as such do not wear down as quickly as the classic Japanese water stones. The 8000 grit stone will perhaps give you the best cutting edge with a mirror polish on chisels and similar blades. Suehiro also makes a small combination stone for those who do not sharpen tools all that often and are reluctant to spend extra for a Cerax stone.
Turning to the sharpeners themselves, we looked at aspects such as ergonomics, speed and simplicity of use, noise level and overall power (for the electric sharpeners), and build quality. We also weighed cost against performance to get a subjective measure of value. After two hours, we had clear picks for the winner and the upgrade choice, as well as an option for people who want high style along with high performance.
Cutting angle – With a manual stick or sharpening stone you set the angle yourself so this does not factor into the equation when choosing that type of sharpener. When shopping for an electric sharpener however it does. You’ll want to decide if you want your knives to have the 15 degree “Asian” style angle so that you can make precise cuts or the Western standard 20 degrees or 22-degree sharpening angle. Most people will opt for the 20 or 22-degree angle simply because their cuisine doesn’t call for a lot of finesse from their knives and those knives are probably of a heavier Western variety anyway.

Hold your knife at approximately 20° in relation to the honing rod. Your angle doesn't need to be exact, just approximate. Whatever angle you decide to choose, or unwittingly end up choosing, make sure to maintain the same angle throughout the honing process. Changing the angle used during the honing process won't smooth out the metal in the blade as much as using a consistent angle will.[4]
A: We’re all told that a sharp knife is safer than a dull knife yet most everyone knows that merely touching a sharp knife can often result in a painful cut while we can wrap our hand around a dull blade with little worry. So why would anyone in their right mind claim that a sharp one is safer than a dull one? To a certain extent it’s a matter of semantics for sure, because there is no denying you have to be extremely careful around really sharp knives. But at the same time there is a very good reason to consider a dull knife to be more of a safety hazard than a sharp knife.
If you’re a serious home chef, we recommend the Chef’sChoice Trizor XV Sharpener. (And we’re not alone: It’s the top pick for Cook’s Illustrated as well.) This model is much more expensive than our top pick, but it produces a professional-quality, polished and honed edge, as opposed to the ProntoPro 4643’s “toothy” edge. “Polished and honed” means it’s inherently sharp: The Trizor XV brings the metal of the blade to an infinitesimally fine point rather than to the relatively coarse edge that our main pick produces. That means you can chop straight down through, say, onions and carrots rather than stroking through them as with a saw. And that makes for faster, more efficient knife work—as long as you possess the knife skills to take advantage. But the Trizor XV is a bit bulky (about the size of a loaf of homemade bread) and heavy, so you’ll need to find space for it under your countertop.

With its premium series Select II, the whetstone manufacturer Sigma Power Corporation from Tokyo addresses users of high-alloy steels such as HSS. These stones, too, are obviously intended to engender a grinding experience similar to that of natural stones. The special production process is expensive, but the Sigma Select II probably has no equal when it comes to demolishing steel.


A: That depends almost entirely on how often you use them. If you are a professional chef who uses his or her knives every day then you should hone them every time you use your knives. But honing has its limits and over time your edge is going to become dull no matter what. Therefore your knives will need to be sharpened at least several times a year. Some chefs, in fact, will use a whetstone on an almost daily basis in order to ensure their knives are always razor sharp. Most of us, however, are not professional chefs and may not even touch our kitchen knives for days at a time. In that case, it’s probably a good idea to hone the edge after every couple of uses and have your knives sharpened once a year.
The kind of tech we love: compact, reliable, durable, attractive and cheap. Purists may feel that other sharpeners will produce a more perfect result but for 99% of the human race this sharpener will be everything the doctor ordered. Your blades stay sharp for a good long time thanks to the 2-stage sharpening process and if you’re a left handed chef you’ll love the fact that it works just as effectively for you as for anyone else.
I've been using these stones for the past day, and they work great. Once you get the technique down that works for you, you can sharpen any knife to the point it can cut through news paper. Tip: make sure you count the amount of times you pass through the stone on one side and do that same amount on the other side. What I usually do is if I know the knife is very dull or chipped, I do 100 passes on each side using the 400 grit. I test the blade on thick paper and if it cuts through I test it on news paper. If it doesn't cut through the news paper I do another 50 passes on each side. Repeat this until the blade can cut through newspaper. After, on the 1000,3000, and then the 8000 grit stone I do 50 passes on each side. This should make the blade very smoothe cutting and polish it. I plan on getting a strop or piece of leather to further polish the blade. The only thing I don't like about this is that this package is that it does not come with a dressing stone so you can re flatten/level the stone after using them.
The unique three stone system features a 6" medium Arkansas, 6" fine Arkansas and 6" coarse synthetic stone mounted on a molded plastic triangle with handles on the end for easy stone selection. The sturdy molded plastic base has non-skid rubber feet for safety, a V-shaped trough to catch oil drippings and easy-to- read stone identification markings.
If you’re sharpening high quality knives, you probably don’t want to use a cheapo sharpening stone. But if you’re just getting started with sharpening your pocket knife, there’s no need to get too fancy right off the bat. You can find a sharpening stone at most hardware stores for about $10. This one is very similar to the one I use. Nothing fancy. Most basic sharpening stones come with two sides: a rough grit and a fine grit. The finer the grit, the finer or sharper you can get your blade. You usually start off sharpening on the rough grit and then finish sharpening it on the finer grit.
http://www.youtube.com/user/MakeSushi1 is all about how to make sushi, we pride ourselves on creating new exciting sushi roll recipes and then sharing them with the world. In our video tutorials we will teach you how to do all a basics of making sushi and create innovative sushi rolls, sashimi, nigiri sushi and possibly might create a new category of sushi , who knows. Subscribe to our YouTube channel to be notified of our weekly sushi videos: http://www.youtube.com/subscription_c...
Functionality – If you have experience with the stick or sharpening stone you likely don’t want or need anything else. If, however, you are in search of an electric-powered sharpener you’ll want to consider how many “stages” you need in your sharpener. In a typical 3-stage sharpener the first stage is the coarsest and does most of the heavy lifting required to turn the edge from dull to sharp. The second stage will have finer grain sharpening wheels. These are used to hone the edge, that is, to smooth out the burrs left by the coarse first stage. A third stage will refine the edge even further and remove any debris left over from the sharpening process.
Start off on the rough grit side of the stone. Check the grit on your stone, or the packaging that came with the stone, to identify which is which. In general, whetstones and diamond stones each have different grits on either side. The rough grit side is used to grind the steel down, while the fine grit side is used to sharpen or hone the knife. The grinding process comes first, so you start on the rough grit side.
Once the burr is removed, it's time to test the sharpness with paper. Hold a piece of newspaper at about 45°, with a bit of tension, and slash lightly with each point of the blade. If it cuts through easily, your knife's sharp. Warner speedily lacerated his newspaper, but I of course struggled. There is an element of technique involved, he reassured me. 
That’s not to say that you need one of these knife sharpeners—as we note below in the next section, you may prefer another type of sharpener, one that arguably produces an even better edge. But the simple, foolproof sharpeners we’ve picked here will satisfy most people, and they all do the job quickly. That means you’ll be far more likely to use one of these, and that means you’ll always have sharp, safe, effective, and enjoyable knives at hand.
I enjoy these stones so much that the feedback is not a deterrent at all for me, I don’t even think about it. The results are always nothing but top notch, they deliver exactly what I want, some of the sharpest knives I have ever produced were sharpened on Shapton Glass stones. They may be thinner but they last a very long time, they are easy to maintain as well,

Jigs, such as the industry-standard Edge Pro, are an extension of the stone method, as they use simple but cleverly designed armatures to maintain a consistent angle between the stone and the blade. They’re extremely effective—professional knife sharpeners are some of their biggest champions—but they’re also expensive, and really practical only with a dedicated workbench.
★ MOST COMPLETE SET ON AMAZON – Our Sharpening Set is the only kit that comes with both a Flattening Stone and Angle Guide in addition to a Bonus E-Book (for sharpening tips and tricks) and Detailed Instruction Guide. Providing amazing value at a lower price than other sets. A Flattening Stone is a MUST have since all whetstones eventually become uneven and need to be flattened. This set completely eliminates the need to buy one later.
Sharpal 102N 5-in-1 Knife and Hook Sharpener features Sharpal 102N 5-in-1 Knife and Hook Sharpener features pre-set crossed carbides for quick edge setting and ceramic stones for fine honing. Multi-groove sharpening stone is designed to sharpen fishhooks of various sizes. It comes with rubber over-molded body and feet for secure and comfortable grip. Moreover integrated compass built-in rust-proof ...  More + Product Details Close

Manufacturer contacted and sent a new one for replacement. Great customer service but replacement item was nicked on the corner. It was still usable so i didn't bother to ask for another replacement. I would recommend item to be shipped in another box instead of an over-sized yellow envelop which is not adequate protection. Item sharpen my knife pretty good though..


The Sharpening and Specialty lines of waterstones from Naniwa are available in several packages of three to five stones. The Specialty line is the same as the Sharpening line, but half the thickness and therefore less expensive. Both the Sharpening and the Specialty stones are 8 1/4" long by 2 3/4" wide, amply sized for most knives and tools. These are a higher grade stone that do not require soaking before use. While you would need a flattening stone in addition, these kits are a good way to enter into premium grade waterstones.
Some of the videos I watched suggested soaking the stone for 12-15 minutes prior to use. One suggested using vegetable oil on the surface versus water/soaking (I used water and presoaking it for 15-minutes). So instead of a simple 'out-of-the-box-and-use' approach, it required a bit of research before sharpening a knife. Otherwise I would have given this product a 5-star rating.
Aesthetics – While it’s true that most people keep their sharpener, (even their expensive mechanical sharpeners) in the drawer until it’s time to use them you’ll still want to be aware of whether your sharpener fits into the overall aesthetic of your kitchen when you do take it out to use. While sharpener designs are fairly limited to be sure you typically have some control over the color and finish of the device as well as design factors like whether the device is boxy or rounded in appearance. With a stone sharpener or a stick however you pretty much get what you get.
The basic concept of sharpening is simple – you're using an abrasive edge to remove metal – but the knife you buy may alter the method you should use. A general rule of thumb is that a waterstone can be used for both Japanese- and Western-style blades, but you should avoid pull-through sharpeners for Japanese knives (or any knife with very brittle blades).
4. Start sharpening the first side of the blade. With your blade set at the prefect angle, you’re ready to start sharpening. Imagine you’re carving off a slim piece of the stone’s surface. Personally, I bring the blade into the stone. Other people stroke the blade away from the stone. Both ways work, so just use whatever technique you prefer. If the knife blade is curved or if it’s longer than the stone, you’ll need to sweep the blade sideways as you work, so the entire edge is sharpened evenly. Apply moderate pressure as you sharpen. No need to bear down hard on the blade. After you make one stroke, start back at the beginning and repeat. Do this about 6-12 times.
Diamond plates are available in various plate sizes (from credit card to bench plate size) and grades of grit. A coarser grit is used to remove larger amounts of metal more rapidly, such as when forming an edge or restoring a damaged edge. A finer grit is used to remove the scratches of larger grits and to refine an edge. There are two-sided plates with each side coated with a different grit.[14]
The Idahone stood out on a couple of fine details, too: Its ergonomic maple wood handle was more comfortable than the synthetic handles on the rest of the competitors, and its hanging ring is amply sized and sturdily made of steel. The other ceramic rods we tested had smaller hanging rings, plastic rings, or no hanging ring at all. Hanging a ceramic rod is a good idea, because the material is somewhat brittle and can chip or break if it gets jostled around in a drawer or utensil holder.
To use a whetstone you run the knife's blade back and forth across the stone's surface and due to the constant friction with the stone, which acts like a piece of sandpaper, the knife's edge becomes razor sharp and has a brilliant mirror shine. If you are a beginner at using a whetstone it can a take a while to master the sharpening process, so here is a video to help you with your sharpening stone skills.

This sharpener includes five different sharpening stones along with a knife clamp that holds the knife during sharpening, and a guide that allows you to select the proper blade angle. Honing oil is also included. The stones have finger grips for a secure hold and are color coded so you know which are coarser and which are finer. Unlike traditional whetstones, with this system the knife remains still while you move the stones along the blade. This manual system allows you to sharpen knives at four different angles, but requires some practice to become comfortable with the technique.

Finally, once you've refreshed the edge on your knife, you need to hone the edge to make it true. What happens when you grind a new edge onto your knife is that the extreme edge of the blade becomes microscopically thin. That is why it's sharp. But being so thin means that it is easily bent to one side or the other, causing the knife to seem dull. It isn't dull, it's what's called out of true.
×