Using the strength of industrial high precision superior mono-crystalline diamonds, Diamond Machining Technology (DMT) have created a durable longer-lasting flat sharpening surface that will efficiently sharpen, hone, deburr and polish almost any type of knife or cutting tool. The DMT set contains 3 one-sided whetstones that have extra-fine, fine, and coarse grits which means you have a complete sharpening system at your fingertips.
I am just starting out sharpening with whet stones. I have found these stones to be very nice and the instructional videos that come along with the set on knifeplanet are extremely helpful to anyone starting out. The cost of the set was very reasonable and seems to be a great value. The customer service is amazing, I lost the site for the videos and sent an email to get the information and immediately there was a reply with all of the links that I needed. I appreciate their attention to their customers!!
You need the right size of sharpening stone that fit the type and size of your blades and tools. In general, 6-inches stones are the smaller models and 8-inches are the larger ones. The stones larger than 8 inches are work best for big-sized blades and tools. You may also find sort of ‘pocket knife sharpener’ out there. Most of the credit card sized sharpening stone are smaller than 6 inches and ideal for on the go sharpening not for regular basis.
I've used ceramic rods, diamond plates, and leather strops for our sharpening needs. And, like most, I've tried a dozen little gimmicky sharpeners that, while some work, those that do often remove way too much material from the edge, making your blade wear down faster. I've also used oil stones, grinders and buffers for less meticulous sharpening of axes and such. These two stones from Unimi (600/1000 and 2000/6000) served as my introduction to whetstone sharpening. And I must say I like it. Though, I'm not sure of the need for investing in more expensive stones.
The toughest angle to master is the angle at which you'll sharpen the edge of the knife. For a Japanese knife, that should be around 12-15 degrees. Before you reach for the protractor, a good test is to get roughly half an index finger's gap between the spine of the knife and the stone (see above). Remember to remove your finger before you start sharpening. For a Western-style knife, you want an angle of about 20°, so raise it ever-so-slightly higher.

Ease of use – Most people in search of a mechanical sharpener want one because they don’t want to be bothered with trying to achieve a perfect edge themselves using a stick or sharpening stone. They want predictable, first class results every time. In that case it’s important that the electric powered device is easy to use, achieves results quickly and with little effort and is designed with user safety in mind. Keep in mind too that it’s easy to apply too much pressure when using a mechanical sharpener and when that happens you’re likely to see unsatisfactory results. In addition there are subtle differences between mechanical devices designed for Asian-style knives and those designed for Western-style knives. This has to do with the sharpening angle discussed above. Don’t get an Asian sharpener if you don’t need precise control over your cuts.
Cutlery is essential to the operation of every commercial kitchen, so it is important to know the best techniques for kitchen knife handling and safety. Proper knife training can help minimize the risk of personal injury and keep your kitchen running smoothly. If you are just beginning to learn or simply need to brush up on your approach, keep reading for some helpful knife safety tips. 1. A Sharp Knife Is a Safer Knife When you use a dull knife to cut, you need to apply more force. As a result, the knife is more likely to slip and increases the risk of injury. Keeping your knives sharpened is one of the easiest ways to keep them safe. Simply use a sharpening stone or knife sharpener to maintain the original precision of the blade. If your
Siliciclastic stone is a clastic, noncarbonate, sedimentary stone that is almost exclusively silica-bearing and exists as either a form of quartz or, another silicate mineral. In addition, hardened clay is also a sedimentary stone but, it is formed from organic materials such as plant and animal matter and thus, it is much softer than Siliciclastic However, when silicon sediment is suspended in a clay matrix and then naturally hardened over thousands of years, it forms an excellent whetstone material; although, it is somewhat softer than Novaculite. Thus, because the geology of Japan once held large deposits of this type of stone it has been used for hundreds of years for sharpening tools, knives, and swords. However, unlike Novaculite, Belgian Blue, and Coticule, both natural and synthetic Japanese whetstones use water for lubrication and thus, they are commonly known as “Japanese Water Stones” because this type of stone is very porous. Thus, natural Japanese Water Stones must be soaked in water for up to twenty-four hours prior to use whereas, synthetic Japanese Water Stones can be soaked for only a few moments.
Diamond hones are made from very small, industrial grade, diamonds adhered to the face of a metal or plastic plate. Also, because Diamonds are so much harder than any of the other sharpening materials, they tend to cut very fast and last much longer than the other whetstone materials. But, they are also often more expensive to purchase. In addition, Diamond Stones generally consist of three different styles consisting of a solid metal plate coated with an adhesive and diamond dust with holes in the plate to allow the swarf to escape, a solid plate without holes for sharpening tools with corners that might catch in the holes, and a plastic plate with islands of exposed plastic interspersed with the adhesive and diamond dust to act as a lubricant.
Siliciclastic stone is a clastic, noncarbonate, sedimentary stone that is almost exclusively silica-bearing and exists as either a form of quartz or, another silicate mineral. In addition, hardened clay is also a sedimentary stone but, it is formed from organic materials such as plant and animal matter and thus, it is much softer than Siliciclastic However, when silicon sediment is suspended in a clay matrix and then naturally hardened over thousands of years, it forms an excellent whetstone material; although, it is somewhat softer than Novaculite. Thus, because the geology of Japan once held large deposits of this type of stone it has been used for hundreds of years for sharpening tools, knives, and swords. However, unlike Novaculite, Belgian Blue, and Coticule, both natural and synthetic Japanese whetstones use water for lubrication and thus, they are commonly known as “Japanese Water Stones” because this type of stone is very porous. Thus, natural Japanese Water Stones must be soaked in water for up to twenty-four hours prior to use whereas, synthetic Japanese Water Stones can be soaked for only a few moments.
A: People often make the mistake of assuming that just because a mechanical knife sharpener will sharpen the edge of a knife that means it will sharpen any type of cutting edge, including scissors. This is a mistake and can wind up being a costly mistake when you have to replace both your scissors and the knife sharpener. There are sharpening devices specifically designed to handle scissors. Or you can bring your scissors to a sharpening pro who will usually have the right equipment on hand to also sharpen scissors. Another thing to keep in mind about trying to use a sharpener to sharpen scissors is that by using the device in this fashion you are likely voiding the warranty. As such if you damage the device trying to sharpen scissors you’ll need to pay to have it repaired or replaced as the warranty won’t cover it. Also, certain types of high end scissors also come with a warranty. And, just as with the sharpener itself, if you try to sharpen them using a mechanical sharpener you can say goodbye to the warranty protection. The bottom line is to always use the appropriate tool for the job at hand. That way you’re assured of the best possible result and any warranty remains in effect.

Sharpening stone set helps you slice through anything with ease when you have a truly razor-sharp knife, chisel, or axe.Made from professional grade Aluminum Oxide, so expensive oil is NOT required; just use some Water and you're good to go. Works better than a diamond sharpening stone for knives.Non-slip bamboo holder keeps everything secure so you never have to worry about the Japanese whetstone slipping off the counter.Whetstone knife sharpener makes all your blades last longer - use the coarse 3000 grit to prep and smoothen the blade then finish honing and polishing with the 8000 side.Slice through anything with ease and achieve the real precision of a pro when you have a truly razor-sharp knife, chisel, or axe.Made from White Corundum, so expensive oil .
Historically, there are three broad grades of Japanese sharpening stones: the ara-to, or "rough stone", the naka-to or "middle/medium stone" and the shiage-to or "finishing stone". There is a fourth type of stone, the nagura, which is not used directly. Rather, it is used to form a cutting slurry on the shiage-to, which is often too hard to create the necessary slurry. Converting these names to absolute grit size is difficult as the classes are broad and natural stones have no inherent "grit number". As an indication, ara-to is probably (using a non-Japanese system of grading grit size) 500–1000 grit. The naka-to is probably 3000–5000 grit and the shiage-to is likely 7000–10000 grit. Current synthetic grit values range from extremely coarse, such as 120 grit, through extremely fine, such as 30,000 grit (less than half a micrometer abrasive particle size).[citation needed]
Like all DMT® products, DMT sharpening stones are proudly made in the USA and will produce excellent, consistent results time after time, year after year. DMT's diamond sharpening stones feature the most diamond per square inch in the industry and a proprietary process that ensures near-perfect consistency in grit size, engineered to be the flattest sharpeners on the market. Simply put, DMT’s premium sharpening stones are best-in-class products with undeniable long-lasting value.
Once the burr is removed, it's time to test the sharpness with paper. Hold a piece of newspaper at about 45°, with a bit of tension, and slash lightly with each point of the blade. If it cuts through easily, your knife's sharp. Warner speedily lacerated his newspaper, but I of course struggled. There is an element of technique involved, he reassured me. 

Manufacturer contacted and sent a new one for replacement. Great customer service but replacement item was nicked on the corner. It was still usable so i didn't bother to ask for another replacement. I would recommend item to be shipped in another box instead of an over-sized yellow envelop which is not adequate protection. Item sharpen my knife pretty good though..
The company is to be commended for including links to instructional videos in the package. Those videos lay out clearly how to get the most from your Whetstone sharpener stone. Once you get up to speed you’ll likely enjoy the process and at the same time achieve professional quality results time and again. Sure, it’s not fancy and doesn’t have a sleek, chrome plated design but it works.
The answer to the question of how to choose a single whetstone from among the many is actually one of both purpose and expense. Indeed, as the old adage says: “You get what you pay for” – This is certainly the case with sharpening stones. In fact, as a general rule, a high quality, natural, whetstone is significantly more expensive than a man-made whetstone but, they also tend to produce a noticeably finer edge than man-made stones do. On the other hand, man-made whetstones (with the exception of diamond hones) are very affordable and, just like natural whetstones, they too are available in different grits for different stages in the sharpening process from cutting the initial edge bevel to polishing a finely honed edge.
The stone is of good quality. It can be used with water or oil - but not both at the same time of course :) ... What I really want to mention is that Hayneedle has amazing customer service - no joke! My stone was shipped from the mfg. not hayneedle whse and there was a chip on one corner. They said - we can't have that! ... So they took care of the whole matter with NO cost to me and they were very friendly as if I was doing them a favor!
Be careful: Don’t move your fingers laterally along the edge, you’ll cut yourself. Feel for a rough area running from tip to heel. Again, it takes time to know what to expect because the best burr will be subtle. Just know that the bigger the burr, the more metal you are removing—more than necessary. Don’t worry, you won’t ruin the knife doing this. You’re learning here, and mistakes are part of the sharpening journey. Learn from them.

Fortunately our product review experts have put their noses to the grindstone (so to speak) for you and come up with a comprehensive list of the 14 best knife sharpeners on the market today. They’ve cast a wide net that includes everything from the most elaborate mechanical devices to the simplest sharpening sticks and stones so you’re bound to find one that fits your needs, temperament and budget. Keep in mind that any opinions expressed here are those of our experts.
A: When it comes to the best knife sharpeners used in a domestic setting the abrasives used to sharpen the blade should last for quite a few years. When they do eventually wear out many of the best manufacturers will refurbish them for you, typically for a nominal fee. Again, however, unless you are using the sharpener on a daily basis (and there is virtually no reason the average person would do this), the sharpener should last for many years before ever needing service.
Cheers to a New Year! ⠀ ⠀ Designed to toast up to 800 slices of bread per hour, the Avatoast conveyor toaster is perfect for businesses with diverse toasting needs. Not only does its 10" wide conveyor belt fit 2 slices side-by-side, but its 3" opening accommodates a variety of products. Easily toast bread, bagels, English muffins, or buns per customer request.⠀ ⠀ ⠀ ⠀ ⠀ Ideal for a variety of applications, use this shaker in your bakery to sprinkle sugar on baked goods, or top your hot, fresh pizza with parmesan cheese at your restaurant or pizza shop. Its durable and attractive stainless steel construction provides exceptional durability for use in your commercial establishment. Plus, the included handle makes it comfortable and easy to use!⠀ ⠀ ⠀ ⠀ Create a clean, elegant tabletop presentation with this Villeroy & Boch Cooking Elements 10 1/4" white porcelain round serving dish / lid. Featuring a fresh, white color, this piece is a professional and attractive serving solution for your restaurant, hotel, or country club dining room.⠀ ⠀ ⠀ ⠀
Some of the videos I watched suggested soaking the stone for 12-15 minutes prior to use. One suggested using vegetable oil on the surface versus water/soaking (I used water and presoaking it for 15-minutes). So instead of a simple 'out-of-the-box-and-use' approach, it required a bit of research before sharpening a knife. Otherwise I would have given this product a 5-star rating.
×